If you run powercfg /batteryreport on a Windows laptop, the top of the report has a line called Connected Standby, and the Recent usage table is full of states like Active, Suspended and Connected standby. A lot of people read "Not supported" as an error. It isn't. Here is how to read it, and how to check which sleep model your machine actually uses.
Two sleep models, one report
Windows laptops sleep in one of two ways:
- S3 (traditional sleep): the system is mostly powered down. Nothing runs until you wake it.
- Modern Standby (S0 Low Power Idle): phone-style sleep. The screen is off and the system idles at very low power, waking briefly for allowed work such as updates or network activity. Microsoft used to call this Connected Standby, and the battery report still uses the old name.
The battery report just tells you which one you have and logs the transitions:
| Report shows | What it means |
|---|---|
Connected Standby: Not supported | The machine isn't using network-connected Modern Standby. Usually S3, sometimes Modern Standby with networking disconnected. Not a fault. |
Suspended rows in Recent usage | The laptop went to sleep (lid closed, Sleep selected, timeout). |
Connected standby rows | The laptop slept using Modern Standby. |
Active | Normal use, screen usually on. |
None of these is a battery-health score. They're states, not grades.
Check the sleep model in one command
powercfg /a Look at the first lines of the output:
-
Standby (S3)listed as available → "Connected Standby: Not supported" is expected. -
Standby (S0 Low Power Idle) Network Connected→ the report normally shows Connected Standby as supported. -
Standby (S0 Low Power Idle) Network Disconnected→ Modern Standby, but the report may still say "Not supported".
Don't try to force a different sleep model with registry tweaks you find online. If sleep works and the battery doesn't drain badly overnight, there's nothing to fix.
Two of my own laptops
I compared reports from two laptops in November 2026:
- An office ThinkPad with a 2015 BIOS:
Connected Standby: Not supported, and every sleep shows up asSuspended. The standby columns elsewhere in the report are empty. - My sister's Lenovo with a 2023 BIOS:
Supported, sleep shows up asConnected standby, and the report adds standby figures to Usage history and Battery life estimates.
The newer laptop's standby estimates are also a good reminder not to trust single numbers. One day it logged 7 h 22 min of Connected standby on battery at a rate of about 1% per 16 hours, which the report turned into an estimate of 1,929 hours on a full charge. Another week it showed 994% per 16 hours. Short sessions get stretched to a 16-hour rate, so a couple of minutes of activity can produce absurd figures. Look at several days before drawing conclusions.
When sleep drain is worth investigating
Some charge loss during sleep is normal. Investigate when the loss is large and repeats.
- In Recent usage, note the charge at the
Suspended/Connected standbyrow and at the nextActiverow. That's your drain for that sleep. - Compare a few nights with similar conditions (same accessories, similar starting charge).
- On a Modern Standby machine, run an admin Command Prompt and generate a SleepStudy report:
powercfg /sleepstudy /duration 7 SleepStudy summarizes each standby session and points at the components that were active during the bad ones. The battery report tells you when and how much; SleepStudy tells you what.
- Check capacity separately. A worn battery makes the same drain look bigger in percent. Compare Design Capacity with Full Charge Capacity in the Installed batteries section.
Common causes of heavy Modern Standby drain: background sync and updates, network activity, a USB device or dock, a driver that blocks deep idle, heat, or the laptop waking up when it shouldn't.
TL;DR
- "Connected Standby: Not supported" = no network-connected Modern Standby. Not a bug.
-
Suspended= sleep.Connected standby= Modern Standby sleep. -
powercfg /atells you which model you have. -
powercfg /sleepstudytells you what drained the battery during Modern Standby.
I wrote up the full version, with the timeline walkthrough and both laptops' screenshots, here: Connected Standby Not Supported: What It Means. Disclosure: it's my site.

